Android Enthusiasts Stack Exchange is a question and answer site for enthusiasts and power users of the Android operating system. It only takes a minute to sign up.
Sign up to join this community
Sometimes I need to have my phone shut down as fast as possible. In older phones I was able to remove the battery, but after some "innovations" this feature is no longer present. Is there any better option than using casual shutdown and waiting for long seconds until it gets down? It is especially bad when I pour water on my phone and the touchscreen refuses to work.
I am using Xiaomo Pocophone F1 with Android 9.0.
In fact without removing battery it's not possible to shut down a device completely in order to avoid the loss that could possibly occur due to short circuit caused by water.
Let's have a brief look at what shut down means and what are possible options to achieve this.
HOW SHUTDOWN WORKS?
Android is based on Linux kernel which is the very first executable of operating system which is run during boot process. Kernel initializes necessary hardware and prepares a basic environment before executing init, the very first userspace process we can see. It's init which then starts and takes care of all services and processes. On shutdown, reverse of this happens.
INIT
When you tap Power Off from Power Menu, or when you issue reboot -p command from terminal app or adb, it sets Android property sys.powerctl to shutdown (with an optional reason for shutdown) which tells init it's time to save any unsaved work to persistent storage, stop all services and processes gracefully (or brutally), sync filesystem caches, un-mount filesystems and then hand over charge to kernel by making syscall reboot (ref). Kernel then makes sure all userspace processes are stopped including init, forcibly unmounts any stubborn filesystems and ultimately powers down hardware devices including CPUs and RAM.
Android's init supports two modes: shutdown and reboot. Linux init has some more shutdown options including halt and poweroff. See this answer for more details.
KERNEL
Most of the time during shut down is taken by init. In order to save time you can bypass init and ask kernel directly for a poweroff by making syscall:
reboot(LINUX_REBOOT_MAGIC1, LINUX_REBOOT_MAGIC2, LINUX_REBOOT_CMD_POWER_OFF)
That's what busybox poweroff -f command or the magic SysRq key O (equivalent to Alt-SysRq-O on a PC) would do (ref). Both should be preceded by sync to avoid damaging filesystems. From commandline we can do:
~# echo 1 >/proc/sys/kernel/sysrq
~# echo s >/proc/sysrq-trigger
~# echo o >/proc/sysrq-trigger
This is the fastest way to shutdown OS on rooted device.
HARD REBOOT
But how to power down the device if even the kernel becomes non-responsive? Hardware can usually take care of this i.e. if you keep power button pressed for a fixed time interval. There's some hard-coded value (mostly 10 seconds) inside Power Management Unit (PMIC). No process will be stopped, no filesystem would be unmounted, no goodbye would be conveyed, just the power will be cut to CPU, RAM and other relevant hardware resources. Most SoCs (which have PMIC embedded inside) implement this as reboot, not shut down.
So to summarize the above lines, there are two ways to shutdown device: through init or calling kernel directly. Both can be achieved through simple shell commands or can be mapped to some hardware key or special key combination. But water can make any hardware key useless, so this method can't be a universal solution.
POWER BUTTON
But the point is, your device isn't fully powered off whichever path you have chosen. During boot process there are things which are powered up before the OS loads (and possibly be powered up even when there is no OS on device). There must be a circuitry in PMIC (e.g. a microcontroller in low-power mode and may be some software stack too) which is always powered up so than it can listen to your request for switching on the device when you press power button for a few seconds, or even when you connect a charger to device in powered-off state.
COMMUNICATION PROCESSOR
Also the baseband processor (BP) - which runs modem and is responsible for all communication through mobile networks e.g. call, SMS and internet - is totally isolated from Application Processor (the one we call CPU) and is not governed by Android kernel; it runs an independent RTOS. And as they say, government agencies may use it to track you even when you think your device is powered off. So it means it may possibly be (partially or fully or periodically) running when Android isn't running.
If nothing else, at least battery terminals are always live, connected to some part of motherboard which may get short when got wet. So if your device isn't water resistant and the battery doesn't have some short-circuit protection built-in, you can never be dead sure your device won't get damaged when water poured on it.
You can shut down your device by holding
Volume Up + Power Button
simultaneously for several seconds.
If you continue to press the power key, it will shut down without confirmation. That takes yet a few more seconds but doesn't require the touchscreen in the event you've described.
p.s. Going on a tangent, I find that locking my screen and wiping it often works if a bit of water messes with the touch screen. But if it's drenched shutting it down would be better for the electronics.
